Coolest 50 T Rex Racings

 

T-Rex Racing 2016 - 2018 Suzuki GSX-S1000F No Cut Frame Front Rear Axle Sliders Case Covers Bar Ends - White Red

T-Rex Racing 2016 – 2018 Suzuki GSX-S1000F No Cut Frame Front & Rear Axle Sliders Case Covers Bar Ends – White & Red

T-Rex Racing 2016 – 2018 Suzuki GSX-S1000F No Cut Frame Front & Rear Axle Sliders Case Covers Bar Ends – White & Red - Material = uhmw-pe (ultra high molecular weight polyethylene) and aircraft grade aluminum brackets. Condition= new. Special feature= the pucks are solid and not hollow, made to withstand a greater impact brackets are designed not to rotate in a lowside. No cut or plastic fairings modification required. Fit models 2016-2018 suzuki gsxs1000f.

 

T-Rex Racing Plastic Spools or Swingarm Sliders 8mm

T-Rex Racing Plastic Spools or Swingarm Sliders 8mm

T-Rex Racing Plastic Spools or Swingarm Sliders 8mm - Uhmw -pe. Spools or swing-arm sliders are bolt-on accessories to the rear swing-arms of the bike the operator will lift the bike with the rear stand from the spools most bikes come with pre-threaded holes for spools priced per pair.

 

T-Rex Racing 2015 - 2017 Suzuki GSX-S750 No Cut Frame Sliders - Black

T-Rex Racing 2015 – 2017 Suzuki GSX-S750 No Cut Frame Sliders – Black

T-Rex Racing 2015 – 2017 Suzuki GSX-S750 No Cut Frame Sliders – Black - Special feature the pucks are solid and not hollow, made to withstand more of an impact. No cut or plastic fairings modification required. Material = uhmw-pe (ultra high molecular weight polyethylene) the brackets are made of steel. Fit models 2015, 2017 suzuki gsx-s750.

 

T-Rex Racing 2012 - 2014 Kawasaki ZX-14R  ZZR1400 Rear Axle Sliders

T-Rex Racing 2012 – 2014 Kawasaki ZX-14R / ZZR1400 Rear Axle Sliders

T-Rex Racing 2012 – 2014 Kawasaki ZX-14R / ZZR1400 Rear Axle Sliders - The installation is a simple bolt on with the bar going through the axle and one plastic puck on each side. They provide indispensable protection for your beautiful expensive swing-arm. It is more dimensional stable than nylon and used in many industrial ball bearing and friction reducing applications. This purchase is for a pair of rear axle sliders. Rest assured that you are getting the best material commercially available. However, due to constant improvement, the frame sliders can sometimes vary slightly from those in the picture. The long bar and inserts inside the sliders are made 6061-t6 aluminum for strength. The slider pucks are made of uhmw-pe (ultra high molecular weight polyethylene), a tough plastic with good strength, wear resistance and dimensional stability. The frame sliders that you will receive will most likely be the ones pictured above.

 

T-Rex Racing 2017 - 2018 Kawasaki Versys-X 300 Engine Guard green

T-Rex Racing 2017 – 2018 Kawasaki Versys-X 300 Engine Guard (green)

T-Rex Racing 2017 – 2018 Kawasaki Versys-X 300 Engine Guard (green) - It is more dimensionally stable than nylon and used in many industrial ball bearing and friction reducing applications. Delrin is harder but more brittle. No need to order a new kit so ride without worry the cnc precision cut pucks are made of uhmw-pe (ultra high molecular weight polyethylene), a tough plastic with good strength, wear resistance and dimensional stability. The guards have four mounting points to increase the strength and prevent the guards from rotating during a lowside. We use highest grade commercially available 12. They also feature replaceable pucks that can be inexpensively purchased. Compared to delrin, it is softer but tougher. It is also braced together in the middle to further increase the strength of the guards. This purchase is for a set of engine guards designed to fit the kawasaki versys-x 300. It is an ideal material for slider where it can absorb more impact onto itself and therefore reduce the direct impact on the frame and engine. 9 (177,000 psi in tensile strength) wherever possible.

 

T-Rex Racing 2016 - 2018 Honda CBR500R No Cut Frame Sliders - Black

T-Rex Racing 2016 – 2018 Honda CBR500R No Cut Frame Sliders – Black

T-Rex Racing 2016 – 2018 Honda CBR500R No Cut Frame Sliders – Black - Fit models 2016, 2018 honda cbr500r. You will receive the exact kit shown in the top most picture. No cut or plastic fairings modification required. Special feature the pucks are solid and not hollow, made to withstand a greater impact the steel tubes are designed not to rotate in a lowside and braced together to increase strength. Material = uhmw-pe (ultra high molecular weight polyethylene) and steel tubing finished in durable red powder coat.

 

T-Rex Racing Buell 1125R  CR  XB9  XB12 Rear Axle Sliders

T-Rex Racing Buell 1125R / CR / XB9 / XB12 Rear Axle Sliders

T-Rex Racing Buell 1125R / CR / XB9 / XB12 Rear Axle Sliders - The long bar and inserts inside the sliders are made 6061-t6 aluminum for strength. They can be inexpensively replaced in case of a low side. The slider pucks are made of uhmw-pe (ultra high molecular weight polyethylene), a tough plastic with good strength, wear resistance and dimensional stability. It is more dimensional stable than nylon and used in many industrial ball bearing and friction reducing applications. Rest assured that you are getting the best material commercially available. Installation is a simple bolt on with the bar going through the axle and one plastic puck on each side. This purchase is for a pair of rear axle sliders for above bike models that help protect your bike expensive swing arms in case of a low side.

 

T-Rex Racing 2009 - 2015 Aprilia RSV4 Complete Protection Kit

T-Rex Racing 2009 – 2015 Aprilia RSV4 Complete Protection Kit

T-Rex Racing 2009 – 2015 Aprilia RSV4 Complete Protection Kit - Material = uhmw-pe (ultra high molecular weight polyethylene) and a aircraft grade aluminum 6061-t6 brackets finished in black anodizing for durability. No cut or plastic fairings modification required. Fit models aprilia 2009 to 2015 rsv4. You will receive the exact kit shown in the top most picture. Special feature the pucks are solid and not hollow, made to withstand a greater impact brackets are designed not to rotate in a lowside.

 

T-Rex Racing 2014-2016 KTM Superduke 1290  R Front Fork Axle Sliders

T-Rex Racing 2014-2016 KTM Superduke 1290 / R Front Fork Axle Sliders

T-Rex Racing 2014-2016 KTM Superduke 1290 / R Front Fork Axle Sliders - It is more dimensionally stable than nylon and used in many industrial ball bearing and friction reducing applications. The slider pucks are made of uhmw-pe (ultra high molecular weight polyethylene), a tough plastic with good strength, wear resistance and dimensional stability. Rest assured that you are getting the best material commercially available. This purchase is for a front axle / fork sliders for above bike models that helps protect your bike expensive fork in case of a low-side. The long bar and inserts inside the sliders are made 6061-t6 aluminum for strength. They can be inexpensively replaced in case of a low-side. Installation is a simple bolt on with the bar going through the axle and one plastic puck on each side.

 

T-Rex Racing 2014 - 2017 KTM 1290 Superduke R No Cut Frame Sliders - Orqange

T-Rex Racing 2014 – 2017 KTM 1290 Superduke R No Cut Frame Sliders – Orqange

T-Rex Racing 2014 – 2017 KTM 1290 Superduke R No Cut Frame Sliders – Orqange - Special feature= the pucks are solid and not hollow, made to withstand a greater impact brackets are designed not to rotate in a lowside. Condition= new. Fit models 2014, 2017 ktm 1290 superduke r. No cut or plastic fairings modification required. Material = uhmw-pe (ultra high molecular weight polyethylene) and a aircraft grade aluminum 6061-t6 brackets finished in black anodizing for durability.

 

T-Rex Racing 2013 - 2016 Yamaha FJR1300  A  AE  ES Engine Luggage Guard Crash Cages Front Axle Sliders - Red Pucks Bar

T-Rex Racing 2013 – 2016 Yamaha FJR1300 / A / AE / ES Engine Luggage Guard Crash Cages Front Axle Sliders – Red Pucks Bar

T-Rex Racing 2013 – 2016 Yamaha FJR1300 / A / AE / ES Engine Luggage Guard Crash Cages Front Axle Sliders – Red Pucks Bar - No cut or plastic fairings modification required. Special feature = the pucks are solid and not hollow, made to withstand a greater impact the steel tubes are designed not to rotate in a lowside multiple mounting points and replaceable uhmw-pe (ultra high molecular weight polyethylene) pucks luggage guard come with aluminum skid plates. Fit models = 2013, 2016 yamaha fjr1300 / a / ae / es. Dimensions= heavy duty tubing with 7/8″ in diameter and 1/8″ in thickness. Material = uhmw-pe (ultra high molecular weight polyethylene) and steel tubing finished in durable black powder coat the bar is aircraft grade stainless steel 304 the bolts are highest grade available at 129 they are zinc galvanized for protection against the elements.

 

T-Rex Racing 2006 - 2007 Kawasaki ZX-10R No Cut Frame Sliders - Black

T-Rex Racing 2006 – 2007 Kawasaki ZX-10R No Cut Frame Sliders – Black

T-Rex Racing 2006 – 2007 Kawasaki ZX-10R No Cut Frame Sliders – Black - The sliders feature a new design of a complete solid puck without a hollowed-out center. This purchase is for a set of frame sliders / plastic body protectors (one lhs and one rhs) for above bike models. The slider pucks can be inexpensively replaced in case of a low side. 9 bolts (177,000 psi in tensile strength) wherever possible. The brackets attach to the frame at multiple locations to avoid rotation that can damage the plastic fairings (see more explanation below). It is more dimensionally stable than nylon and used in many industrial ball bearing and friction reducing applications. The bracket is bolted to the engine mount and the aluminum spacer is bolted to the bracket. We use highest grade commercially available 12. Rest assured that you are getting the best material commercially available. The slider puck is then screwed on to the spacer. Delrin is harder but more brittle. It is an ideal material for slider since it can absorb more impact force onto itself and therefore reduce the impact on the frame and engine. Compared to delrin, it is softer but tougher. Since this spacer is made of solid billet aluminum there is no need for re-tightening the engine bolt in the long run where you have to do so with plastic slider as the plastic would gradually give in and therefore making the bolt loose. The slider pucks are made of uhmw-pe (ultra high molecular weight polyethylene), a tough plastic with good strength, wear resistance and dimensional stability. This increases the strength and contact surface to about 30%.

 

T-Rex Racing No Cut Frame Sliders for Yamaha FZ8 Fazer and FZ1

T-Rex Racing No Cut Frame Sliders for Yamaha FZ8 Fazer and FZ1

T-Rex Racing No Cut Frame Sliders for Yamaha FZ8 Fazer and FZ1 - It is more dimensionally stable than nylon and used in many industrial ball bearing and friction reducing applications. The spacer is bolted to the engine mount and the slider puck is screwed onto it. Since this spacer is made of solid billet aluminum there is no need for re-tightening the engine bolt in the long run where you have to do so with plastic slider as the plastic would gradually give in and therefore making the bolt loose. 9(177,000 psi in tensile strength) wherever possible. The puck material are made of uhmw-pe (ultra high molecular weight polyethylene), a tough plastic with good strength, wear resistance and dimensional stability. We use highest grade commercially available 12. This increases the strength and contact surface to about 30%. The slider pucks can be inexpensively replaced in case of a low-side. These sliders feature a new design of a complete solid puck without a hollowed-out center. Compared to delrin, it is softer but tougher. Rest assured that you are getting the best material commercially available. It is an ideal material for slider since it can absorb more impact force onto itself and therefore reduce the impact on the frame and engine. Delrin is harder but more brittle.

 

T-Rex Racing Single One Arm Rear Stand for Ducati Diavel 1098 1198 S 1199 1299 Streetfighter S - Black

T-Rex Racing Single One Arm Rear Stand for Ducati Diavel 1098 1198 S 1199 1299 Streetfighter S – Black

T-Rex Racing Single One Arm Rear Stand for Ducati Diavel 1098 1198 S 1199 1299 Streetfighter S – Black - Reversible single arm rear stand= the stand fits ducati 1098 s/r and 1198 s, panigale, streetfighter s, diavel, 1199, 1299, xdiavel, hypermotard 939, hyperstrada 939, monster 1200, multistrada 1200 and comes with two pins. The stand was cleansed in chemical bath, stabilized zinc phosphate coating and finally finished with electrostatic powder coating to prevent it from the elemental degradation. Long handle bar gives extra leverage and can be reversed to forward direction. The center wheel-stop rod prevents the rear wheel from spinning during removal. The upright rectangular tubing provides unbeatable strength. The stand requires a simple bolt on assembly. The stand comes with one pin that will fit both sides. The pin is made of uhmw-pe polymer to prevent marring the inside of the axle and 6061-t6 aluminum for strength. Ball bearing pins allow the rear wheel spin easily while being lifted. It can be used to lift the bike from either side. The over-sized washer and the butterfly nut are attached onto the rod to prevent bike from sliding off the stand as the wheel spins. The threaded rod is inserted through the axle hole to the other side of the wheel.

 

T-Rex Racing 2008-2015 Suzuki Hayabusa GSX-R1300 Rear Axle Sliders

T-Rex Racing 2008-2015 Suzuki Hayabusa GSX-R1300 Rear Axle Sliders

T-Rex Racing 2008-2015 Suzuki Hayabusa GSX-R1300 Rear Axle Sliders - The replacement nut and cross bar are made of 304 grade stainless steel for strength and rust-resistance. The purchase is for a pair of rear axle sliders for above bike models. Rest assured that you are getting the best material commercially available. The nuts are made of grade 8, nylon lock type so they won’t back out under normal engine vibration. It is more dimensional stable than nylon and used in many industrial ball bearing and friction reducing applications. The slider pucks are made of uhmw-pe (ultra high molecular weight polyethylene), a tough plastic with good strength, wear resistance and dimensional stability.

 

T-Rex Racing 2014 - 2016 Kawasaki Z1000 No Cut Frame Sliders

T-Rex Racing 2014 – 2016 Kawasaki Z1000 No Cut Frame Sliders

T-Rex Racing 2014 – 2016 Kawasaki Z1000 No Cut Frame Sliders - Fit models 2014, 2016 kawasaki z1000. Material = uhmw-pe (ultra high molecular weight polyethylene) and a aircraft grade aluminum 6061-t6 bracket finished in black anodizing for durability. No cut or plastic fairings modification required. Special feature the pucks are solid and not hollow, made to withstand a greater impact brackets are designed not to rotate in a low-side.

 

T-Rex Racing 2013-2017 Yamaha FZ-07 MT-07 Front Axle Sliders

T-Rex Racing 2013-2017 Yamaha FZ-07 MT-07 Front Axle Sliders

T-Rex Racing 2013-2017 Yamaha FZ-07 MT-07 Front Axle Sliders - The slider puck is made of uhmw-pe (ultra high molecular weight polyethylene), a tough plastic with good strength, wear resistance and dimensional stability. It is used in many industrial ball bearing and friction reducing applications. Rest assured that you are getting the best material commercially available. The bolt is made of 304 stainless steel. It is softer than delrin as the result it can absorbs more impact and is less susceptible to cracking. It allows the fork to slide on the plastic puck instead of the fork itself. The installation is a simple bolt on with the bar going through the axle and one plastic puck on each side. This purchase is for front axle / fork sliders for above bike models. That helps protect your bike front fork in case of a low-side. They can be inexpensively replaced in case of a low-side.

 

T-Rex Racing Honda 919  CB 599  CB600F  CB900F  CBR600 F4i Spool Adapters

T-Rex Racing Honda 919 / CB 599 / CB600F / CB900F / CBR600 F4i Spool Adapters

T-Rex Racing Honda 919 / CB 599 / CB600F / CB900F / CBR600 F4i Spool Adapters - The angle on the swing-arms makes it worse. This purchase is for spool adapters for the above bike model. This plastic keeps the aluminum brackets from scratching the swing-arms. The spools are made of uhmw-pe. It can cause the bike to slip off the stand and fall. They are designed to securely attach to the swing-arms and allow safely lifting of the rear wheel using a paddock stand. The swing-arms have no threaded holes for spools and are at an angle. Lifting the rear of the honda can be challenging. If you want anodized spools, please specify during checkout. Without spools the bike can be difficult to lift with a stand. The aluminum brackets are lined with uhmw-pe (ultra high molecular weight polyethylene), a tough plastic with good strength and wear resistance. The adapters come in black only. T-rex spool adapters are made to meet this challenge. Once lifted, it can be unstable.

 

T-Rex Racing 2013 - 2017 Yamaha FZ-09  MT-09  FJ-09 No Cut Frame Front Rear Axle Sliders Spools - Black

T-Rex Racing 2013 – 2017 Yamaha FZ-09 / MT-09 / FJ-09 No Cut Frame Front & Rear Axle Sliders Spools – Black

T-Rex Racing 2013 – 2017 Yamaha FZ-09 / MT-09 / FJ-09 No Cut Frame Front & Rear Axle Sliders Spools – Black - Fit models  2013, 2017 yamaha fz-09 / mt-09 / fj-09. Special features the pucks are solid and not hollow, made to withstand a greater impact brackets are designed not to rotate in a lowside. No cut or plastic fairings modification required. You will receive the exact kit shown in the top most picture. Material = uhmw-pe (ultra high molecular weight polyethylene) and a aircraft grade aluminum 6061-t6 brackets finished in black anodizing for durability.

 

T-Rex Racing 2013 - 2017 Yamaha FZ-09  MT-09  FJ-09 Rear Axle Sliders

T-Rex Racing 2013 – 2017 Yamaha FZ-09 / MT-09 / FJ-09 Rear Axle Sliders

T-Rex Racing 2013 – 2017 Yamaha FZ-09 / MT-09 / FJ-09 Rear Axle Sliders - This purchase is for a pair of rear axle sliders for above bike models. The installation is a simple bolt on with the bar going through the axle and one plastic puck on each side. However, due to constant improvement, the frame sliders can sometimes vary slightly from those in the picture. The long bar and inserts inside the sliders are made 6061-t6 aluminum for strength. They provide indispensable protection for your beautiful expensive swing-arm. The frame sliders that you will receive will most likely be the ones pictured above. It is more dimensionally stable than nylon and used in many industrial ball bearing and friction reducing applications. The slider pucks are made of uhmw-pe (ultra high molecular weight polyethylene), a tough plastic with good strength, wear resistance and dimensional stability. Rest assured that you are getting the best material commercially available.

 

T-Rex Racing 2006 - 2014 Kawasaki ER-6N  Versys 650 No Cut Frame Sliders

T-Rex Racing 2006 – 2014 Kawasaki ER-6N / Versys 650 No Cut Frame Sliders

T-Rex Racing 2006 – 2014 Kawasaki ER-6N / Versys 650 No Cut Frame Sliders - Fit models = 2006, 2014 kawasaki er-6n / versys 650. No cut or plastic fairings modification required. Special feature the pucks are solid and not hollow, made to withstand a greater impact. Slider dimensions approx 6″ in length, 2″ in diameter for the longer puck, 45″ in length, 2″ in diameter for the shorter puck. Material = uhmw-pe (ultra high molecular weight polyethylene) and solid steel brackets finished in durable black powder coat.

 

T-Rex Racing 2013-2015 Yamaha FZ-07 MT-07 Rear Axle Sliders

T-Rex Racing 2013-2015 Yamaha FZ-07 MT-07 Rear Axle Sliders

T-Rex Racing 2013-2015 Yamaha FZ-07 MT-07 Rear Axle Sliders - This purchase is for a pair of rear axle sliders. The long bar and inserts inside the sliders are made 6061-t6 aluminum for strength. They provide indispensable protection for your beautiful expensive swing-arm. It is more dimensionally stable than nylon and used in many industrial ball bearing and friction reducing applications. Rest assured that you are getting the best material commercially available. The installation is a simple bolt on with the bar going through the axle and one plastic puck on each side. The slider pucks are made of uhmw-pe (ultra high molecular weight polyethylene), a tough plastic with good strength, wear resistance and dimensional stability.

 

T-Rex Racing 2012 - 2016 Honda CBR1000RR No Cut Frame Sliders

T-Rex Racing 2012 – 2016 Honda CBR1000RR No Cut Frame Sliders

T-Rex Racing 2012 – 2016 Honda CBR1000RR No Cut Frame Sliders - Material = uhmw-pe (ultra high molecular weight polyethylene) the brackets are made of aircraft grade aluminum 6061-t6. No cut or plastic fairings modification required. Fit models = 2012, 2016 honda cbr1000rr. Special feature = the pucks are solid and not hollow, made to withstand a greater impact the brackets are designed not to rotate in a low side and braced together to increase strength. Condition=new.

 

T-Rex Racing 2008 - 2016 Yamaha WR250R  WR250X No Cut Frame Sliders Front Rear Axle Sliders Combo

T-Rex Racing 2008 – 2016 Yamaha WR250R / WR250X No Cut Frame Sliders Front & Rear Axle Sliders Combo

T-Rex Racing 2008 – 2016 Yamaha WR250R / WR250X No Cut Frame Sliders Front & Rear Axle Sliders Combo - The slider pucks are made of uhmw-pe (ultra high molecular weight polyethylene), a tough plastic with good strength, wear resistance and dimensional stability. This purchase is for a pair of frame, front and rear axle sliders for the above bike model. The bolt is made of solid stainless steel. It is more dimensionally stable than nylon and used in many industrial ball bearing and friction reducing applications. Rest assured that you are getting the best material commercially available.

 

T-Rex Racing Honda CB300F  CBR250R  CBR300R Adjustable Kickstand

T-Rex Racing Honda CB300F / CBR250R / CBR300R Adjustable Kickstand

T-Rex Racing Honda CB300F / CBR250R / CBR300R Adjustable Kickstand - This purchase is for an adjustable lowered kick stand for above bike models. However, it will fit your particular bike model. It is absolutely a must-have if you lowered your bikes. The kick stand that you will receive may vary slightly from the pictures depicted in the listing. It can go from stock height to approximately 3″ lower.

 

T-Rex Racing 2017-2018 Kawasaki Ninja 650 ABS Z650 Z900 Front Fork Axle Sliders

T-Rex Racing 2017-2018 Kawasaki Ninja 650 /ABS Z650 Z900 Front Fork Axle Sliders

T-Rex Racing 2017-2018 Kawasaki Ninja 650 /ABS Z650 Z900 Front Fork Axle Sliders - The installation is a simple bolt on with the bar going through the axle and one plastic puck on each side. It is softer than delrin as the result it can absorbs more impact and is less susceptible to cracking. This purchase is for a pair of front axle / fork sliders that help protect your bike in case of a low-side. The bolt is made of 304 stainless steel. It is used in many industrial ball bearing and friction reducing applications. Rest assured that you are getting the best material commercially available. The slider puck is made of uhmw-pe (ultra high molecular weight polyethylene), a tough plastic with good strength, wear resistance and dimensional stability. It allows the fork to slide on the plastic puck instead of the fork itself. They can be inexpensively replaced in case of a low-side.

 

T-Rex Racing 2010 -2017 BMW R nine T  Racer S1000R  S1000RR Front Axle Sliders

T-Rex Racing 2010 -2017 BMW R nine T / Racer S1000R / S1000RR Front Axle Sliders

T-Rex Racing 2010 -2017 BMW R nine T / Racer S1000R / S1000RR Front Axle Sliders - 9 (177,000 psi in tensile strength). It allows the fork to slide on the plastic puck instead of the fork itself. The installation is a simple bolt on with the bar going through the axle and one plastic puck on each side. The bolts are made of highest grade commercially available 12. The long bar is made of billet aluminum. The sliders are made of uhmw-pe (ultra high molecular weight polyethylene), a tough plastic with good strength, wear resistance and dimensional stability. It is more dimensionally stable than nylon and used in many industrial ball bearing and friction reducing applications. Rest assured that you are getting the best material commercially available. This purchase is for a pair of front axle / fork sliders for above bike models that help protect your bikes front fork in case of a low-side.

 

T-Rex Racing 2013-2015 Honda CB500F No Cut Frame Sliders

T-Rex Racing 2013-2015 Honda CB500F No Cut Frame Sliders

T-Rex Racing 2013-2015 Honda CB500F No Cut Frame Sliders - Fit models = 2013-2015 honda cbr500f. Material = uhmw-pe (ultra high molecular weight polyethylene) and a aircraft grade aluminum 6061-t6 brackets finished in black anodizing for durability. No cut or plastic fairings modification required. Brand = t-rex racing. Special feature the pucks are solid and not hollow, made to withstand a greater impact brackets are designed not to rotate in a lowside.

 

T-Rex Racing 2017 Kawasaki Versys-X 300 Skid Plate

T-Rex Racing 2017 Kawasaki Versys-X 300 Skid Plate

T-Rex Racing 2017 Kawasaki Versys-X 300 Skid Plate - The skid plate is made from precision cnc machined aircraft grade aluminum finished with black powder coating for durability. Rest assured that you are getting the best material commercially available. This purchase is for one skid plate for the kawasaki versys-x 300, designed to protect your bike from dirt, mud, and other debris.

 

T-Rex Racing 2015 - 2017 Yamaha YZF-R1 Rear Axle Sliders

T-Rex Racing 2015 – 2017 Yamaha YZF-R1 Rear Axle Sliders

T-Rex Racing 2015 – 2017 Yamaha YZF-R1 Rear Axle Sliders - It is more dimensionally stable than nylon and used in many industrial ball bearing and friction reducing applications. This translates to a significant increase in strength. Rest assured that you are getting the best material commercially available. Unlike our traditional center-hollow plastic pucks, the new pucks are completely solid and have up to 35 percent more surface area. The purchase is for a set of rear axle sliders that fit the above mentioned make and models. The bar is made out of air-craft grade 6061-t6 aluminum and coated in a uv-resistant anodized finish. The sliders are made of uhmw-pe (ultra high molecular weight polyethylene), a tough plastic with good strength, wear resistance and dimensional stability.

 

T-Rex Racing 2015 - 2017 Suzuki GSX-S750 Engine Case Covers

T-Rex Racing 2015 – 2017 Suzuki GSX-S750 Engine Case Covers

T-Rex Racing 2015 – 2017 Suzuki GSX-S750 Engine Case Covers - Fit models suzuki 2015, 2017 gsx-s750. Material = uhmw-pe (ultra high molecular weight polyethylene) and a aircraft grade aluminum 6061-t6 brackets finished in black anodizing for durability. Special feature the pucks are solid and not hollow, made to withstand a greater impact brackets are designed not to rotate in a lowside. No cut or plastic fairings modification required. You will receive the exact kit shown in the top most picture.

 

T-Rex Racing 2013 - 2017 Yamaha FZ-09  MT-09  FJ-09 Front Axle Sliders

T-Rex Racing 2013 – 2017 Yamaha FZ-09 / MT-09 / FJ-09 Front Axle Sliders

T-Rex Racing 2013 – 2017 Yamaha FZ-09 / MT-09 / FJ-09 Front Axle Sliders - That helps to protect your bikes front fork in case of a low-side. It allows the fork to slide on the plastic puck instead of the fork itself. 9(177,000 psi in tensile strength). This purchase is for a pair of front axle / fork sliders for above bike models. However, due to constant improvement, the frame sliders can sometimes vary slightly from those in the picture. The installation is a simple bolt on with the bar going through the axle and one plastic puck on each side. The long bar is made of billet aluminum. The frame sliders that you will receive will most likely be the ones pictured above. Rest assured that you are getting the best material commercially available. It is more dimensionally stable than nylon and used in many industrial ball bearing and friction reducing applications. The sliders are made of uhmw-pe (ultra high molecular weight polyethylene), a tough plastic with good strength, wear resistance and dimensional stability. The bolts are made of highest grade commercially available 12.

 

T-Rex Racing Silver Anodized Aluminum Spools or Swingarm Sliders 10mm

T-Rex Racing Silver Anodized Aluminum Spools or Swingarm Sliders 10mm

T-Rex Racing Silver Anodized Aluminum Spools or Swingarm Sliders 10mm - Material = steel tubing finished in durable black powder coat the bolts are highest grade available at 129 they are zinc galvanized for protection against the elements. Note these are for the top portions of the 1150gs adventure guards only you must use the touratech bottom portions for them to work. No cut or plastic fairings modification required. Spools or swing-arm sliders are bolt-on accessories to the rear swing-arms of the bike the operator will lift the bike with the rear stand from the spools most bikes come with pretreated holes for spools the above picture is only a representation of the many different colored spools this auction is only for one pair of spools we have black, blue, orange, red and silver please pick a color by sending us an email or leave us a note during checkout we will send out the most available spools in stock if color of choice is not picked.

 

T-Rex Racing 1999 - 2005 BMW R1150GS Engine Guard Crash Cages

T-Rex Racing 1999 – 2005 BMW R1150GS Engine Guard Crash Cages

T-Rex Racing 1999 – 2005 BMW R1150GS Engine Guard Crash Cages - Note these are for the top portions of the 1150gs adventure guards only you must use the touratech bottom portions for them to work. No cut or plastic fairings modification required. Fit models bmw 1999, 2005 r1150gs. Material = steel tubing finished in durable black powder coat the bolts are highest grade available at 129 they are zinc galvanized for protection against the elements.

 

T-Rex Racing 2015 - 2017 Yamaha YZF-R1 Front Axle Sliders

T-Rex Racing 2015 – 2017 Yamaha YZF-R1 Front Axle Sliders

T-Rex Racing 2015 – 2017 Yamaha YZF-R1 Front Axle Sliders - Unlike our traditional center-hollow plastic pucks, the new pucks are completely solid and have up to 35 percent more surface area. Rest assured that you are getting the best material commercially available. The bar is made out of air-craft grade 6061-t6 aluminum and coated in a uv-resistant anodized finish. This translates to a significant increase in strength. The purchase is for a set of front axle sliders that fit the above mentioned make and models. It is more dimensionally stable than nylon and used in many industrial ball bearing and friction reducing applications. The sliders are made of uhmw-pe (ultra high molecular weight polyethylene), a tough plastic with good strength, wear resistance and dimensional stability.

 

T-Rex Racing 2017 - On Yamaha FZ-09 MT-09 Fender Eliminator Kit with bonus items

T-Rex Racing 2017 – On Yamaha FZ-09 MT-09 Fender Eliminator Kit with bonus items

T-Rex Racing 2017 – On Yamaha FZ-09 MT-09 Fender Eliminator Kit with bonus items - This purchase is for a fender eliminator kit for the above bike model. This kit also allows the use of the stock and aftermarket signal lights. Backed by a limited lifetime warranty so rest assured that you are getting the best material commercially available. It also comes with a replaceable axle block slider with engraved graduation lines. The fender eliminator includes cnc precision cut brackets designed to keep out unwanted debris, dirt, mud, and etc.

 

T-Rex Racing 2017 Yamaha YZF-R6 No Cut Frame Sliders w aluminum puck inserts Blue

T-Rex Racing 2017 Yamaha YZF-R6 No Cut Frame Sliders w/ aluminum puck inserts (Blue)

T-Rex Racing 2017 Yamaha YZF-R6 No Cut Frame Sliders w/ aluminum puck inserts (Blue) - Rest assured that you are getting the best material commercially available. They can be inexpensively replaced in case of a lowside. It is an ideal material for slider where it can absorb more impact onto itself and therefore reduce the direct impact on the frame and engine. It is more dimensionally stable than nylon and used in many industrial ball bearing and friction reducing applications. 9 (177,000 psi in tensile strength) wherever possible. Our new 2017 kit now features aluminum inserts to prolong the puck life while saving you more money the slider puck are made of uhmw-pe (ultra high molecular weight polyethylene), a tough plastic with good strength, wear resistance and dimensional stability. Delrin is harder but more brittle. The brackets are made from aircraft grade aluminum 6061-t6 finished in black anodizing to increase its durability. Compared to delrin, it is softer but tougher. We use highest grade commercially available 12. This purchased is for a pair of frame sliders for the 2017 yamaha yzf-r6.

 

T-Rex Racing 2013 - 2017 Yamaha FZ-09  MT-09  FJ-09 Engine Case Covers

T-Rex Racing 2013 – 2017 Yamaha FZ-09 / MT-09 / FJ-09 Engine Case Covers

T-Rex Racing 2013 – 2017 Yamaha FZ-09 / MT-09 / FJ-09 Engine Case Covers - That helps protect your bikes engine case and stator cover in the event of a low-side. They can be inexpensively replaced in case of a low-side. The slider pucks are made of uhmw-pe (ultra high molecular weight polyethylene), a tough plastic with good strength, wear resistance and dimensional stability. 9 (177,000 psi in tensile strength). Rest assured that you are getting the best material and fully thought out product. The bolts are made of highest grade commercially available 12. It is more dimensionally stable than nylon and used in many industrial ball bearing and friction reducing applications. This purchase is for a pair of engine case cover sliders and a stator cover slider (one lhs and one rhs) for above bike models.

 

T-Rex Racing 2008 - 2016 Ducati Diavel Frame Front Quick Release Rear Axle Sliders - Black

T-Rex Racing 2008 – 2016 Ducati Diavel Frame Front Quick Release Rear Axle Sliders – Black

T-Rex Racing 2008 – 2016 Ducati Diavel Frame Front Quick Release Rear Axle Sliders – Black - No cut or plastic fairings modification required. Material = uhmw-pe (ultra high molecular weight polyethylene), high strength neodymium magnets, and a aircraft grade aluminum 6061-t6 brackets finished in black anodizing for durability. Fit models = ducati 2008, 2016 diavel. Special features = the pucks are solid and not hollow, made to withstand a greater  impact brackets are designed not to rotate in a lowside.

 

T-Rex Racing 2018 Triumph Street Triple RS Rear Axle Sliders

T-Rex Racing 2018 Triumph Street Triple RS Rear Axle Sliders

T-Rex Racing 2018 Triumph Street Triple RS Rear Axle Sliders - The installation is a simple bolt on with the bar going through the axle and one plastic puck on each side. It is more dimensionally stable than nylon and used in many industrial ball bearing and friction reducing applications. The slider pucks are made of uhmw-pe (ultra high molecular weight polyethylene), a tough plastic with good strength, wear resistance and dimensional stability. Rest assured that you are getting the best material commercially available. The long bar and inserts inside the sliders are made 6061-t6 aluminum for strength. They provide indispensable protection for your beautiful expensive swing-arm. This purchase is for a pair of rear axle sliders.

 

T-Rex Racing 2012 - 2014 Kawasaki ZX-14R  ZZR1400 Front Axle Sliders

T-Rex Racing 2012 – 2014 Kawasaki ZX-14R / ZZR1400 Front Axle Sliders

T-Rex Racing 2012 – 2014 Kawasaki ZX-14R / ZZR1400 Front Axle Sliders - However, due to constant improvement, the frame sliders can sometimes vary slightly from those in the picture. The bolts are made of highest grade commercially available 12. It allows the fork to slide on the plastic puck instead of the fork itself. The frame sliders that you will receive will most likely be the ones pictured above. The long bar is made of billet aluminum. The installation is a simple bolt on with the bar going through the axle and one plastic puck on each side. The sliders are made of uhmw-pe (ultra high molecular weight polyethylene), a tough plastic with good strength, wear resistance and dimensional stability. Rest assured that you are getting the best material commercially available. It is more dimensionally stable than nylon and used in many industrial ball bearing and friction reducing applications. 9 (177,000 psi in tensile strength). This purchase is for a pair of front axle / fork sliders that help protect your bikes front fork in case of a low-side.

 

T-Rex Racing 2018 Triumph Street Triple RS Front Axle Sliders

T-Rex Racing 2018 Triumph Street Triple RS Front Axle Sliders

T-Rex Racing 2018 Triumph Street Triple RS Front Axle Sliders - The spacers are made out of air-craft grade 6061-t6 aluminum and coated in a uv-resistant anodized finish. Rest assured that you are getting the best material commercially available. This translates to a significant increase in strength. It is more dimensionally stable than nylon and used in many industrial ball bearing and friction reducing applications. The sliders are made of uhmw-pe (ultra high molecular weight polyethylene), a tough plastic with good strength, wear resistance and dimensional stability. The bolts are made of highest grade commercially available 12. Unlike our traditional plastic pucks, the new pucks are completely solid and have up to 30% the surface area than the old ones. 9 (177,000 psi in tensile strength). This purchase is for a set of front axle sliders that fit the above mentioned make and model.

 

T-Rex Racing Black Anodized Aluminum Spools or Swingarm Sliders 8mm

T-Rex Racing Black Anodized Aluminum Spools or Swingarm Sliders 8mm

T-Rex Racing Black Anodized Aluminum Spools or Swingarm Sliders 8mm - Special featurethe pucks are solid and not hollow, made to withstand more of an impact. Material = uhmw-pe (ultra high molecular weight polyethylene) the brackets are made of steel. No cut or plastic fairings modification required. Fit models suzuki 2015, 2017 gsx-s750.

 

T-Rex Racing 2014-2016 KTM Superduke 1290  R Rear Axle Sliders

T-Rex Racing 2014-2016 KTM Superduke 1290 / R Rear Axle Sliders

T-Rex Racing 2014-2016 KTM Superduke 1290 / R Rear Axle Sliders - It provides indispensable protection for your beautiful expensive swing-arm. This purchase is for a rear axle slider. The and inserts inside the sliders are made 6061-t6 aluminum for strength. Rest assured that you are getting the best material commercially available. The slider pucks are made of uhmw-pe (ultra high molecular weight polyethylene), a tough plastic with good strength, wear resistance and dimensional stability. It is more dimensionally stable than nylon and used in many industrial ball bearing and friction reducing applications. The cross bar are made of 304 grade stainless steel for strength and rust-resistance. The nuts are made of grade 8, nylon lock type so they won’t back out under normal engine vibration.

 

T-Rex Racing 2017 - 2018 Suzuki SV650 Rear Axle Sliders

T-Rex Racing 2017 – 2018 Suzuki SV650 Rear Axle Sliders

T-Rex Racing 2017 – 2018 Suzuki SV650 Rear Axle Sliders - Multiple items can be combined for discount shipping. Rest assured that you are getting the best material commercially available. For our swingarm stands, frame sliders and please click t-rex stands. It is more dimensionally stable than nylon and used in many industrial ball bearing and friction reducing applications. The installation is a simple bolt on with the bar going through the axle and one plastic puck on each side. They provide indispensable protection for your beautiful expensive swing-arm. This purchase is for a pair of rear axle sliders above bike models. The long bar and inserts inside the sliders are made 6061-t6 aluminum for strength. The slider pucks are made of uhmw-pe (ultra high molecular weight polyethylene), a tough plastic with good strength, wear resistance and dimensional stability.

 

T-Rex Racing 2017 Suzuki GSX-R1000 Engine Case Covers

T-Rex Racing 2017 Suzuki GSX-R1000 Engine Case Covers

T-Rex Racing 2017 Suzuki GSX-R1000 Engine Case Covers - This uhmw-pe plastic of 15mm thickness will replace the flimsy stock 3mm cover and provide much more protection to the engine case in a lowside. Rest assured that you are getting the best material commercially available. The covers are made of uhmw-pe (ultra high molecular weight polyethylene). This auction is for a set of engine case covers that helps protect your bike. 9 (177,000 psi in tensile strength). The bolts are made of the highest grade commercially available 12.

 

T-Rex Racing 2008 - 2010 Buell XB9  XB12 No Cut Frame Sliders

T-Rex Racing 2008 – 2010 Buell XB9 / XB12 No Cut Frame Sliders

T-Rex Racing 2008 – 2010 Buell XB9 / XB12 No Cut Frame Sliders - Fit models = buell 2008, 2010 xb9 / xb12. Slider dimensions = approx 2″ and 3″ in length and 2″ in diameter. Material = uhmw-pe (ultra high molecular weight polyethylene) brackets are made of aircraft grade aluminum 6061-t6 bracket finished in black anodizing for durability. No cut or plastic fairings modification required. Special feature = the pucks are solid and not hollow, made to withstand a greater impact the brackets are designed not to rotate in a low side.

 

T-Rex Racing 2013 - 2017 Yamaha FZ-09  MT-09  FJ-09 No Cut Frame Sliders - Black

T-Rex Racing 2013 – 2017 Yamaha FZ-09 / MT-09 / FJ-09 No Cut Frame Sliders – Black

T-Rex Racing 2013 – 2017 Yamaha FZ-09 / MT-09 / FJ-09 No Cut Frame Sliders – Black - No cut or plastic fairings modification required. Special feature the pucks are solid and not hollow, made to withstand a greater impact brackets are designed not to rotate in a lowside. You will receive the exact kit shown in the top most picture. Material = uhmw-pe (ultra high molecular weight polyethylene) and a aircraft grade aluminum 6061-t6 brackets finished in black anodizing for durability. Fit models  yamaha 2013, 2016 fz-09 & mt-09.

 

T-Rex Racing 2015 - 2017 Suzuki GSX-S750 No Cut Frame Front Rear Axle Sliders Case Cover Spool Adapters -Black

T-Rex Racing 2015 – 2017 Suzuki GSX-S750 No Cut Frame Front & Rear Axle Sliders, Case Cover, Spool Adapters -Black

T-Rex Racing 2015 – 2017 Suzuki GSX-S750 No Cut Frame Front & Rear Axle Sliders, Case Cover, Spool Adapters -Black - Fit models suzuki 2015, 2017 gsx-s750. No cut or plastic fairings modification required. Special featurethe pucks are solid and not hollow, made to withstand more of an impact. Material = uhmw-pe (ultra high molecular weight polyethylene) the brackets are made of steel.

 

T-Rex Racing 2011 - 2017 Aprilia RSV4 No Cut Frame Sliders

T-Rex Racing 2011 – 2017 Aprilia RSV4 No Cut Frame Sliders

T-Rex Racing 2011 – 2017 Aprilia RSV4 No Cut Frame Sliders - Color = black. Materials = uhmw-pe (ultra high molecular weight polyethylene) and a aircraft grade aluminum 6061-t6 bracket finished in black anodizing for durability. No cut or plastic fairings modification required. Fit models = 2011, 2017 aprilia rsv4. Special features = the pucks are solid and not hollow, made to withstand a greater impact brackets are designed not to rotate in a lowside.